IC-F1000D/01 ICOM Portable Digital ICOM Transceiver Rx-Tx: 136-174MHz type-D trunking submersible IP67. Supplied with Battery Belt Clip Charger and Antenna

GENERAL
Frequency coverage (MHz): 136–174MHz IC-F2000D 
Number of channels: 16 channels
Type of emissions: 16K0F3E 11K0F3E
                          8K50F3E 4K00F1E/D
Channel spacing: 30KHz 15 KHz 6.25KHz
                        25KHz 12.5KHz 6.25KHz
Power supply requirement: 7.5V DC nominal
Current drain:
                  TX High:1.3 A
                  RX Max. auidio/ Sandby: 400mA (internals SP)/110mA 
Antenna impedance:    50Ω
Operating temperature range:    -30°C to 60°C; –22°F to 140°F (radio specifications)
Dimensions (W×H×D)
(Projections not included):    52.2×111.8×30.3 mm; 2.06×4.4×1.19 in (With BP-280)
Weight:    260g; 9.17oz (With MB-133 and BP-280)

TRANSMITTER
Output power: 5W 2W 1W (Hi L2 L1)
Max. frequency deviation: ± 5.0kHz/±2.5kHz (Wide/Narrow)
Frequency stability: ±1.0ppm
Spurious emissions: 70dB min.
FM hum and noise: 6/40dB typ. (Wide/Narrow)
Audio harmonic distortion: 2.0%/1.1% typ. (W/N)
                                    (AF 1kHz 40% deviation) IC-F2000D
FSK error: 5.0% max.
Ext. microphone connector: 3-conductor 2.5 (d) mm (1⁄10")⁄2.2kΩ

RECEIVER
Sensitivity (at 12dB SINAD): 0.21μV typ.
                                       –8dBμV emf typ.
 Adjacent channel selectivity: 76/53dB typ. (W/N) 
Spurious response: 80dB min.
Intermodulation: 75/75/71dB typ. (W/N/D)
Hum and noise: 47/43dB typ. (W/N) 
Ext. speaker connector: 2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Audio output power (at 5% distortion):
        Internal SP (w/12Ω load): 800mW typ. (at 5% distortion)
        External SP (w/8Ω load): 400mW typ. (at 5% distortion)

Measurements were made following TIA-603.
All stated specifications are subject to change without notice or obligation.
25kHz bandwidth is no longer available for FCC Part 90 licensees for USA versions.
Ask your dealer if you need 25kHz bandwidth.

Applicable U.S. Military Specifications
Icom makes rugged products that meet MIL-STD requirements and strict environmental standards.

Standard                                        MIL 810 F
                                         Method               Proc
Low Pressure                         500.5                I II
High Temp.                           501.5                I II
Low Temp.                            502.5                I II
Temp. Shock                         503.5                I
Solar Radiation                      505.5                I
Rain Blowing/Drip                   506.5                I III
Humidity                               507.5                  –
Salt Fog                               509.5                   –
Dust Blowing                         510.5                  I
Immersion                            512.5                  I
Vibration                               514.6                 I
Shock                                  516.6                  I IV

It also meets equivalent MIL-STD-810-C -D -E and -F

                             Ingress Protection Standard
Dust & Water:    IP67 (Dust-tight and waterproof protection)

2024-02-23 11:55:17

Page: 4